
pluto
pluto
About
- Username
- pluto
- Location
- mars
- Joined
- Visits
- 151
- Last Active
- Roles
- Member
- Location
- mars
Comments
-
Thanks for your input William. Great point, probably I will re think this again.
-
Hi @laumung, I am also trying to integrate multiple ADS1299 using DaisyChain, It would be grate if you can describe, how did you resolve 0xff from all the ADS1299, and what casued the issue? Thanks & Regards, Pluto
-
Hi @Momin_2089 I assume they used the below library: https://github.com/openbci-archive/OpenBCI_8bit/tree/master/OpenBCI_8bit_Library/OpenBCI_8 Hope this helps.
-
Thanks for your input William, we have mailed it to OpenBCI team, hoping to receive their response soon on this.
-
Thanks for your valuable input and constant support William. Pluto
-
Hi @William, Thanks a lot for your help, I could flash the device and host successfully. Regarding programming Chip (Pic32), do we need to follow Cyton programming tutorial? Thanks & Regards, Pluto
-
Thanks for your response nanomike.
-
Could you program it?
-
Hi, I was going through this thread, and while uploading RadioPassThru32Bit code to the fabricated dongle, I am getting an error: The Switch on dongle is towards Reset position. @wjcroft, appreciate your help.
-
Hi William, We tried flashing the RadioDevice32bit to the board, that is DEVICE. We got an error message saying the following: Appreciate your help on this.
-
Hi, in the instruction to program, there is a mention of blue-button on board: Cyton board version we have is: V3-32, is the capacitor already present on board?
-
Thanks for your input.
-
Thanks for the update William.
-
Thanks a lot for your help William. Will follow the same and update.
-
Sure, thanks.
-
Yes, Which procedure to follow for freshly fabricated Boards, cyton & dongle? Should we follow cyton radios guide? Or, first cyton radios then cyton program? Also, after following the steps in cyton radios programming guide, no RFDuino b…
-
Thanks for replying, The links mentioned in the guide has expired / or moved. After following the above links, I am getting redirected to below website:
-
@Shirley @retiutut Hope you can help me here.
-
Works with marker mode in cyton SDK. Thanks.
-
Thanks for your reply William (@wjcroft), Regarding the pin contacts between cyton and daisy, there is no loose connection found. I doubt ADS1299 chip on daisy to be non-functional, as it is working with other Cyton board we have. Could you…
-
No, we haven't received any suggestion from the team regarding failing SD Card reader module. On further testing, we found that, the SD Card module is working fine only when Cyton alone is used, but fails when daisy is connected.
-
@wjcroft Yes. They have suggested - 1. To follow the SD card formatting steps mentioned on the documentation page. 2. To use the latest GUI release. Even after taking care of the above-mentioned points, still the error persists. Kindly let …
-
Thanks for responding @wjcroft. @retiutut To add on, we tried multiple FAT32 formatted SD cards and firmware 3.1.2 was reflashed. But, we noticed that the issue occurs only when we use Cyton+Daisy together. Is there a possibility of interfacing …
-
@wjcroft @retiutut Appreciate your help on this.
-
Hi @sagarchaturvedi, I wanted to know the 16 channel electrodes locations too. Were you able to get (x,y,z) coordinates for 16 channel electrodes for OpenBCI Cyton and Daisy? It would be of great help if you can share those. Thanks, Pluto
-
Hi william, Appreciate your respone. Is there any python code available that derives the railed logic from data?
-
Thanks William and Richard for your response on this. We will be proceeding ahead with the fix as of now. Regards, Pluto
-
@Shirley said: @pluto Thank you for your post. i will bring this cyton SD card streaming/recording data issue to the attention of the engineers tomorrow morning. This will likely require a firmware-level fix, and could take weeks. In meanti…
-
@wjcroft said: It seems likely that if the dongle is sufficiently close to the Cyton, that packet loss would be zero. Providing that there are not other interfering wireless sources in the area. If this is the case it seems possible for you to dr…
-
Yes William, we are using USB extension cord. Yes, we are using the GUI to set distinct bluetooth channel as the two cyton boards should not communicate on same channel as suggested in OpenBCI docs.